Can I Set Up A Bathtub Myself?
Book A ServiceWe've stumbled upon this post relating to How to Install a Bathtub listed below on the net and thought it made perfect sense to relate it with you over here.
Installing a tub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a new one is likewise a moderately tough job. If the old bathtub is conveniently obtainable, the task can relocate quickly; if you have to open a wall to eliminate the old tub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you may need an expert plumber to make tube connections.
This short article will help you install a brand-new tub in your restroom if you have already bought a brand-new bathtub and also do not need to change the setup of your previous water pipelines.
Your tools and material list need to consist of the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The process of removing the existing taps can be fairly troublesome due to the limited access that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a towel ready for the continuing to be water that will certainly originate from the pipelines. Once the supply pipelines have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The former kind needs to be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; after that do the very same for the various other faucet.
Activate the water supply and check all joints as well as new pipework for leaks as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub must wait till the bath tub has actually been utilized a minimum of when as this will certainly settle it into its final setting.
Getting ready for the Setup
First of all, the supporting frame supplied with the bath should be fitted (if called for) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack an inflexible seal, causing the water to permeate the wall surface between the bathroom and the tiling, causing complications with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes as well as cartridges, and also can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can split relatively very early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very serious about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you enjoyed the new entry. So long as you appreciated our blog posting please make sure you remember to pass it around. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Automated Marketing